Marc Billow
037dc9722f
The remote-control-off write block was device-wide and unconditional: whenever a device reports remote control off, every write is rejected with a user-facing error, on the assumption the device would reject it anyway. Issue #54 reports a washer where that assumption doesn't hold -- default detergent/softener dosing writes through even with remote control off, since they apply to the built-in programs too, not just a custom remote-controlled cycle. Add a per-device options flow (Settings > Devices & Services > this device > Configure) with a single toggle, stored in entry.options (not entry.data) so it doesn't affect the device's identity/unique_id. coordinator.async_send_command reads it ahead of the existing remote_control_enabled() check; defaults to False everywhere, so devices that don't touch this option see no change in behavior.
50 lines
2.1 KiB
Python
50 lines
2.1 KiB
Python
DOMAIN = "localthings"
|
|
|
|
PLATFORMS = [
|
|
"sensor", "binary_sensor", "switch", "number", "select", "button",
|
|
"time", "climate", "fan",
|
|
]
|
|
|
|
CONF_HOST = "host"
|
|
CONF_PORT = "port"
|
|
CONF_CA_CERT_PEM = "ca_cert_pem"
|
|
CONF_CA_KEY_PEM = "ca_key_pem"
|
|
CONF_LEAF_CERT_PEM = "leaf_cert_pem"
|
|
CONF_LEAF_KEY_PEM = "leaf_key_pem"
|
|
|
|
# Options-flow key (entry.options, not entry.data): lets a user override the
|
|
# device-wide remote-control-off write block for a specific device (issue
|
|
# #54). Some devices report remote control off yet still accept certain
|
|
# writes (e.g. default detergent/softener dosing on a washer, applied even
|
|
# to the built-in programs) -- the block exists to give a clear error
|
|
# instead of a silent device-side rejection, but that assumption doesn't
|
|
# hold for every model. Defaults to False (block stays on) everywhere it's
|
|
# read, so devices this doesn't apply to see no behavior change.
|
|
CONF_BYPASS_REMOTE_CONTROL = "bypass_remote_control_lock"
|
|
|
|
# The DTLS/CoAP local API binds somewhere in this ephemeral range; which port
|
|
# depends on firmware. Newer builds answer on 49154/49155, but older ones have
|
|
# been seen as low as 49153, so we sweep the whole range for a live UDP port
|
|
# before attempting the (expensive) DTLS handshake.
|
|
PROBE_PORT_RANGE = list(range(49152, 49161))
|
|
|
|
# Ports we've historically seen complete a DTLS handshake. When more than one
|
|
# port in the range looks live, these are tried first.
|
|
PREFERRED_PROBE_PORTS = [49154, 49155]
|
|
|
|
# Per-port timeout for the cheap UDP liveness sweep. Closed ports return an
|
|
# ICMP port-unreachable almost immediately; a live-but-silent port is only
|
|
# detected by this timeout elapsing, so keep it short.
|
|
LIVENESS_PROBE_TIMEOUT_S = 1.5
|
|
|
|
# Deadline for the blockwise /device/0 GET during the config-flow probe. The
|
|
# slowest device observed returns a full dump in ~8s, so 10s leaves headroom
|
|
# without stalling setup; it matches the per-resource read timeout elsewhere.
|
|
PROBE_GET_TIMEOUT_S = 10.0
|
|
|
|
SUMMARY_INTERVAL_S = 30.0
|
|
|
|
DEVICE_SUPPORT_ISSUE_URL = (
|
|
"https://github.com/mbillow/localthings/issues/new?template=device-support.yml"
|
|
)
|